Weird.jpg
Weird.jpg
what do you think this is?
-
Kansas Rust Buzzard
- Posts: 540
- Joined: Fri Dec 28, 2018 9:33 pm
what do you think this is?
You do not have the required permissions to view the files attached to this post.
Re: what do you think this is?
Looks like a picture of 2 windmills! Sure isn’t a picture of me!
“What we’ve got here, is, failure to communicate “
Re: what do you think this is?
Look closely. One mill is in front of the building and the other is behind it….
“What we’ve got here, is, failure to communicate “
Re: what do you think this is?
The big one is furled and the other is not.
“What we’ve got here, is, failure to communicate “
-
Kansas Rust Buzzard
- Posts: 540
- Joined: Fri Dec 28, 2018 9:33 pm
Re: what do you think this is?
Yes, I know there are two, I think they are the same brand but what brand do you think they are?
-
Challenge 27
- Posts: 43
- Joined: Fri Jan 04, 2019 4:19 pm
Re: what do you think this is?
Going to go way out on a limb here ...
Maybe they are Curries. It is hard to tell, but with the closer windmill it looks like the outer wheel rim goes around the outer ends of the blades. If it is a Currie, the multiplicity of blades would make it almost certainly a 10 footer (I'm not sure, think Currie probably made only one size of blade; adding more of them as the wheel diameter increased). If so, it appears that one or more blades have been blown out.
The profile of the vane sheet is similar to that of the older or original Currie vane (see the Field Guide, page 178).
One can see the silhouette of the head, about all that can be said is that it is compatible with the idea that it is a Currie; or more properly does not rule out the possibility of it being a Currie.
Challenge 27
P.S. Or maybe I should stop doing replies at 4:00 in the morning!
Maybe they are Curries. It is hard to tell, but with the closer windmill it looks like the outer wheel rim goes around the outer ends of the blades. If it is a Currie, the multiplicity of blades would make it almost certainly a 10 footer (I'm not sure, think Currie probably made only one size of blade; adding more of them as the wheel diameter increased). If so, it appears that one or more blades have been blown out.
The profile of the vane sheet is similar to that of the older or original Currie vane (see the Field Guide, page 178).
One can see the silhouette of the head, about all that can be said is that it is compatible with the idea that it is a Currie; or more properly does not rule out the possibility of it being a Currie.
Challenge 27
P.S. Or maybe I should stop doing replies at 4:00 in the morning!
Re: what do you think this is?
I like your thought for what it's worth.
-
Windcatcher530 Dan
- Posts: 1925
- Joined: Sun Mar 28, 2021 4:06 pm
- Location: Alcove N.Y.i buy and restore
Re: what do you think this is?
A blurred photo of two windmills !! Did I win the contest?
-
Kansas Rust Buzzard
- Posts: 540
- Joined: Fri Dec 28, 2018 9:33 pm
Re: what do you think this is?
I am leaning towards the Currie, the photo was in the teens so the time frame would be right but it would be unusual for a new one to loose so many sails unless they didn't tighten the bolts up? I will post another photo from a few miles down the road later, I think it is a Currie also but it doesn't look exactly right to me. Thanks
-
Windcatcher530 Dan
- Posts: 1925
- Joined: Sun Mar 28, 2021 4:06 pm
- Location: Alcove N.Y.i buy and restore
Re: what do you think this is?
Well I might as well put in my two cents. As far as I know the largest mill Currie made was a 10ft and the mills in the photo have way to many sails for a 10ft mill. Just my opinion !!!
